概述

HXD - I航行信号灯控制器是1块操作显示面板和2块接线单元组成，操作面板通常嵌入式安装在驾驶台上。航行信号灯控制板主要用于船舶航行中对航行信号灯的监视和控制。HXD - I可测控28路航行信号灯并显示28路航行信号灯的开闭状态。一旦某个信号灯断丝或相应电缆断线时，操作显示面板上对应的LED指示灯即会闪光，并发出声音报警。按消声按钮，即可消声。

航行灯控制器面板上具有触摸式调光按钮，可根据需要对LED指示灯调光。HXD - I航行信号灯控制器可采用两路电源自动切换供电，一路AC220V，一路DC24V也可选择两路AC220V，当出现电源故障时，电源指示灯闪烁，并发出声音报警。

HXD-I航行灯信号灯控制器完全符合CCS通函中提出的MSC 253（83）--航行灯、航行灯控制器和相关设备制定性能标准，带有两个串行接口，接口应符合相关国际标准IEC61162，使报警传送至外部系统并从外部系统接收报警的确认，并可通过控制器上的RS485通讯接口接VDR设备进行数据记录。

技术参数

※ 通道………………………………………24路/28路航行信号灯控制
※ 电源………………………………………………… 24VDC / 220VAC
※ 通讯接口……………………………………………RS485/RS232接口
※ 操作温度………………………………………………………-15℃-55℃
※ 内部功耗……………………………………………………………10W
※ 继电器输出触点………………………………………………………5A
※ 负载功率范围……………………………………………………5-100W
※ 相对湿度……………………………………5%至95%间，非冷凝状态
※ 外壳材料…………………………………………………………………铁
※ 外壳颜色………………………………………………………………黑色
※ 开孔尺寸………………………………………144mm(L) X 240mm(W)
※ 外型尺寸………………………………………165mmX285mmX50mm
※ 副板尺寸…………………………………………412mmX142mmX60mm

  

Navigation light controller HXD-I

Overview

       Navigation light controller of HXD-I series consists of one display model and two connection units. Commonly, the control panel is embedded installed on the bridge. The Navigation light controller is used to monitor and control the Navigation light during sailing. HXD-I can detect the status of 28 Navigation lights, once some wire or signal cable broken, the power operation lights will blink, the alarm will sound at the same time, then you can press the silent-button to stop.

       The control board has touchable dimmer button, you can change the brightness of the LED. HXD-I control board has two auto-switched power: AC220V and DC24V or both AC220 available. When all the way in which a power failure, power light flashes and alarm sounds.

       HXD-I Navigation light controller compliant fully with circular MSC 253 (83) raised by CSS—the standard of the Navigation controller and related devices’ performance. It consists of two serial ports, compliant with the ISO IEC61162, and can send the alarm signal to peripherals, the RS-485 interface can also connect to VDR device to record the data.

 Technical parameters

Channel ... ... ... ... ... ... ... 24 Road / 28 Road navigation signal control
Power... ... ... ... ... ... ... ... ... ...  ... ... ... ... ... ... ... ... ... ... .24VDC / 220VAC
Communication Interface... ... ... ... ... ... ... ... ... RS485/RS232 Interface
Operating temperature  ... ... ... ...  ... ... ... ... ... ... ... ... ... ... -15 ℃ -55 ℃
Internal power consumption ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 10W
Relay output contacts ... ... ... ... ... ...5A/24VDC 1A/220VACLoad power
 range ... ... ... ... ... ... ... ... ... ...  ... ... ... ... ... ... ... ... ... ... ... ...  ... ... 5-100W
Relative humidity ... ...  ... ... ...  ... ... ... ... ... .5-95%, the non-condensing
Case Material ... ... ... ... ... ... ... ... ...  ... ... ...  ... ... ... ... ... ..... ... ... ... ... Iron
Case Color ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .Black
Hole size ... ... ... ... ... ... ...  ... ... ... ... ... ... ... ... 144mm (L) X 240mm (W)
Vice-plate size ... ... ... ... ... ... ... ... ... ... ... ... ... ...412mmX142mmX60mm
Dimensions ... ... ...  ... ... ... ... ... ... ... ... ... ... ... ...165mmX285mmX50mm